Serving Edmonton and surrounding areas since 2017.
Airflow guide

Adjusting room airflow for better comfort

Simple steps for using your room supply registers during the heating and cooling seasons.

A room that feels too warm or too cool may need a small adjustment at its supply register—the vent that blows heated or cooled air into the room. This guide shows you how to use the register’s own lever or wheel and check whether the room feels better.

Start with the room vents

  1. Find the supply register.

    With the heating or cooling running, look for the room vent that blows air out. Many floor and wall registers have a small lever, slider or wheel on the face that opens and partly closes the flaps behind it.

  2. Keep the air path clear.

    Move rugs, furniture and curtains away from supply registers. Keep return-air grilles—the vents that draw air back into the system—open and unobstructed. Do not cover or close returns.

  3. Use only the register’s normal control.

    Adjust a register you can reach safely from the floor. Use only a control you can adjust without tools or removing the cover. If the control is stuck, missing or unclear, leave it alone and ask us for help.

To get more air into a room

  1. Open that room’s supply register.

    Gently move its lever, slider or wheel towards the open position. Controls vary: look at whether the flaps open wider rather than assuming a particular direction. Stop if it resists.

  2. Check the room during normal use.

    Leave the thermostat at your usual setting and allow several heating or cooling cycles before judging the room temperature. Keep a note of the adjustment so you can put it back if needed.

  3. Ask for help if it is already fully open.

    Opening a register cannot fix every cold or warm room. If the room still gets very little air, or feels worse when its door is closed, tell us. Do not close vents around the house to try to force air into it.

To reduce air in a room

Follow your equipment and installer instructions first. If a register is labelled to stay open, or your instructions say to leave all registers open, do not partly close it. Otherwise, if a room gets too much heated or cooled air, try one small adjustment at that room’s supply register:

  1. Partly close the register.

    Move its normal control a little towards closed, leaving a generous opening. Do not shut it completely, cover it with a magnetic cover, or close a group of registers.

  2. Check comfort before changing it again.

    Allow several normal heating or cooling cycles. If the room feels better, leave it there. There is no single correct lever position for every room.

  3. Undo a change that causes trouble.

    If the register starts whistling or the system becomes noisier, return it to its previous position. If the room needs a large reduction to feel comfortable, contact us for an assessment.

Dealing with a draught? If your register has adjustable direction blades, gently aim the air away from where you sit or sleep. Those blades may change direction without changing the amount of air. Do not bend fixed slats.

Review the rooms when the season changes

During the heating season

Start with the supply registers open in rooms that feel cold. In a room that consistently feels too warm, try a small partial adjustment. Keep heat reaching every room, including rooms you use less often.

During the cooling season

Open the supply registers in rooms that feel too warm. Upstairs or sunny rooms may need more cooling, while a room that feels too cold may benefit from a small partial adjustment. Use blinds or curtains to reduce direct sun without blocking the vents.

Base changes on how each room feels. There is no rule to close every upstairs register in winter or every basement register in summer. Note your settings, make one change at a time, and review them when you switch between heating and cooling. Leave any professionally labelled settings as instructed.

When to call Heating and Cooling Doctor Ltd

Contact us if a room stays uncomfortable with its register open, airflow is weak throughout the house, or adjustments cause noise. If the equipment keeps stopping, avoid repeated resets and call us.

If you see ice on the air conditioner, turn cooling off at the normal thermostat if it is safe and dry to use, then call us. Do not chip off the ice or restart cooling before the cause is assessed. If water is near electrical equipment, stay away from it and get qualified help; do not touch wet equipment or electrical controls.

We handle ductwork, duct dampers and equipment adjustments. You do not need to cut ducts, change furnace settings or alter the HRV to follow this guide. Tell us which rooms are affected, the season, and what you have already tried.

Browse homeowner guides · Troubleshooting and maintenance